How to configure Citycell Zoom USB Modem for Linux (EC325)

Today I have configured the CDMA USB modem (HUWAEI EC325) provided by citycell with their zoom connection to use in my linux distro (Mandriva Spring 2007) – Heres how to-

Attach the modem with your pc/laptop

1. check if the USB device is detected properly
cat /proc/bus/usb/devices

you will get some output like this

…..
…..
T: Bus=02 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.01 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=16 #Cfgs= 1
P: Vendor=12d1 ProdID=1001 Rev= 0.00
S: Manufacturer=Huawei Technologies
S: Product=Huawei Mobile
S: SerialNumber=HUAWEI EC3X1
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=pl2303
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=128ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=0b(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=pl2303
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
…..
…..

2. Now probe for this USB device
modprobe usbserial vendor=0x12d1 product=0x1001

3. Now check with dmesg if it has been successfully probed
dmesg

you will get some output like this

[ 2315.412106] usbcore: registered new interface driver usbserial
[ 2315.412508] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
[ 2315.461938] usbcore: registered new interface driver usbserial_generic
[ 2315.461945] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[ 2315.480382] drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
[ 2315.480414] pl2303 2-6:1.0: pl2303 converter detected
[ 2315.480608] usb 2-6: pl2303 converter now attached to ttyUSB0
[ 2315.480620] pl2303 2-6:1.1: pl2303 converter detected
[ 2315.480691] usb 2-6: pl2303 converter now attached to ttyUSB1

4. Now configure your wvdial.conf as shown here.
vi /etc/wvdial.conf

[Modem0]
Modem = /dev/ttyUSB0
Baud = 230400
SetVolume = 0
Dial Command = ATDT
Init1 = ATZ
FlowControl = Hardware (CRTSCTS)
[Dialer cdma]
Username = waps
Password = waps
Phone = #777
Stupid Mode = 1
Inherits = Modem0

Now save this file

You are done!!

Now you can connect to internet by applying the following command in shell

wvdial cdma

Thats it!

%d